Book A Service

 

 

How do you really feel in relation to Tools You Need to Install a New Bathtub ?

Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently obtainable, the job can relocate immediately; if you have to open a wall to remove the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This post will help you mount a brand-new tub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in place between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The former kind must be attached to the faucet ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Setting up the Tub

Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are practical in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by examining the level and also changing the feet on the bath tub up until the level reviews degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the water supply and also examine all joints and new pipework for leakages and tighten them if necessary. Load the tub and also examine the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub should wait till the bath tub has actually been made use of at least once as this will settle it into its final placement.

 

 

Planning for the Setup

Firstly, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to prevent stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or waterproof sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We are very involved in How to Install a Bathtub and I hope you enjoyed reading our page. For those who appreciated our blog entry kindly be sure to pass it around. Thank you so much for taking the time to read it.

Quote & Schedule